Disc Spring Stacks and Series Combinations: Load and Height
How a Disc Spring Stack Turns Single Discs into a Defined Load-Deflection Curve
A single disc spring is a stiff, short-travel element, but very few applications use one disc alone. By arranging several discs on a guide rod, engineers build a disc spring stack whose rate, travel and installed height can be tuned to the mechanism. The arrangement is not a packaging detail: it decides how the assembly behaves under load and how much space it occupies inside the housing.
The two basic rules are simple to state. Discs placed in parallel, all facing the same direction, add their forces at a common deflection, so the stack becomes stiffer without gaining travel. Discs placed in series, alternately inverted, share the deflection and keep the force of a single disc, so the stack becomes softer and gains travel. Real assemblies usually mix both ideas in groups, which is why the term series combination appears so often in spring drawings.
Because each disc in a parallel group carries the full load, the stress per disc rises with group size, and friction between nested discs changes the measured curve on loading and unloading. The catalogue data for a single disc therefore cannot be multiplied blindly. Our disc spring range is produced to the dimensional series of DIN 2093, which gives designers a consistent starting point for building these combinations.
Standards, Materials and the Limits of the Series Combination
DIN 2093 defines the group 1, 2 and 3 dimension series for disc springs, and it is the reference most drawings cite when a stack is specified. The standard fixes the relationship between outer diameter, inner diameter, thickness and cone height, so a series combination assembled from different suppliers still fits the same rod and bore. Where a project needs a non-standard ratio, the geometry has to be agreed on the drawing rather than assumed.
Material Choice and Heat Treatment for Disc Springs
Disc springs are commonly made from quenched and tempered spring steels, typically used in the range 40-50 HRC, because the cone form relies on high yield strength in a small section. Stainless grades such as 1.4310 and 1.4401, covered by EN 10270-3, are chosen where corrosion resistance matters more than peak load. For hot-formed or heavy sections, alloy spring steels such as 60Si2Mn and 51CrV4 are widely used.
Surface condition matters as much as the base grade. Spring surfaces are usually tested for decarburisation, and safety critical parts are checked for cracks with magnetic particle inspection, since a decarburised skin on a thin cone edge will crack long before the calculated stress is reached. Corrosion protection is selected to suit the environment, with zinc-nickel plating, zinc flake and epoxy powder coating among the common systems, and salt spray testing per ASTM B117 used to compare them.
The same discipline applies across our other product families, from coil compression springs to torsion parts, where EN 13906-1 and EN 15800 govern design and quality. A stack is only as predictable as the individual discs feeding it.
Selecting a Stack: Load, Height and the Arithmetic Behind It
Start from the working envelope. Free length, solid height and load at a specified installed height are the three dimensions most often controlled on a spring drawing, and for a stack the solid height is simply the sum of the disc thicknesses in the parallel groups plus any spacer washers. Travel available is the difference between free height and solid height, reduced by a practical margin so the discs are never flattened in service.
Next, decide the force. If a single disc gives the required load at the working deflection, a series combination of n discs gives roughly n times the travel at the same force, provided friction is ignored. A parallel group of m discs gives m times the force at the same deflection. Combining the two gives a stack of m parallel groups in series, with force multiplied by m and travel multiplied by the number of groups.
| Arrangement | Force vs single disc | Travel vs single disc |
|---|---|---|
| Parallel group (same direction) | Multiplied by disc count | Unchanged |
| Series combination (alternating) | Unchanged | Multiplied by disc count |
| Groups in series | Multiplied by group size | Multiplied by number of groups |
Use the spring rate calculator to check the single-disc curve before multiplying, and confirm the coil-side equivalents with the same logic used for helical parts, where rate follows k = G d^4 / (8 D^3 n). For a broader set of design checks, the free engineering tools cover load, stress and packing questions in one place.
FAQ
How much extra travel does a series combination of five discs add?
Five identical discs stacked in series share the deflection, so the assembly travels about five times as far as one disc at the same force. Friction and seat losses reduce the measured value, so verify on a prototype.
Why does a parallel group of discs show a different curve on unloading?
Nested discs rub against each other at the cone faces, and friction opposes motion in both directions. The unloading curve therefore sits below the loading curve, and lubrication or surface treatment changes the size of that gap.
Which DIN 2093 group should I choose for a given rod diameter?
The group follows the outer-to-inner diameter ratio and the thickness series defined in DIN 2093. Select the group that matches your rod and bore first, then adjust the number of discs to reach the required load.
Closing Notes on Stack Design
Treat the stack as a system: fix the installed height, confirm the solid height leaves a margin, then choose the parallel and series pattern that delivers the load without overstressing any single disc.
Send your drawing, load point and envelope to liu@chenjisprings.com or call +86 158 5311 1612, and the team at CHENJI SPRINGS will review the arrangement with you. You can also Request a Quote directly, or browse the full spring product range to see how disc stacks sit alongside our other families.
