Compression Spring Tolerances: EN 13906-1 and EN 15800 Explained
Why compression spring tolerances matter on the drawing
Compression spring tolerances define how closely a manufactured coil must match the dimensions and loads on your drawing. In practice, the three dimensions most often controlled are free length, solid height, and load at a specified installed height. When those values drift, stack height, preload, and fatigue margins change even if wire diameter and coil count look correct on paper.
European buyers usually anchor design to EN 13906-1 for cylindrical helical compression springs made from round wire and bar, then specify acceptance against EN 15800 for cold coiled compression springs made of round wire. Together they separate calculation logic from shop-floor quality rules, which is why procurement teams ask for both references on the same purchase order.
Wire diameters commonly range from 0.1 mm to 60 mm, so tolerance bands that work for fine wire may be impractical for heavy bar coils unless the drawing states inspection points clearly. CHENJI SPRINGS (chenjisprings.com) supplies custom coils where drawing tolerances are agreed before production, including safety-critical parts checked for decarburisation and cracks with magnetic particle inspection when required.
If you are scoping a new part, start from a proven coil family such as custom compression coils and carry the same tolerance philosophy through rate verification and incoming inspection.
EN 13906-1, EN 15800, and spring wire grades
EN 13906-1 covers the design calculation of cylindrical helical compression springs made from round wire and bar. It gives engineers a shared method to relate geometry, material stiffness, and stress so that compression spring tolerances on load and height trace back to calculated spring rate. Rate follows k = G d^4 / (8 D^3 n), with d as wire diameter, D as mean coil diameter, and n as the number of active coils.
EN 15800 defines quality specifications for cold coiled compression springs made of round wire. It is the document buyers cite when they need repeatable free length, solid height, and load checks without rewriting an entire corporate quality manual. Cold-coiled compression springs are usually made from patented cold drawn wire per EN 10270-1 (grades SL, SM, SH, DH), while oil hardened and tempered spring steel wire is covered by EN 10270-2 (grades FDC, TDC, VDC).
Stainless, alloy bar, and cross-reference standards
Stainless spring steel wire is covered by EN 10270-3 (grades 1.4310, 1.4401), and EN 10270-3 and ASTM A313 cover stainless spring wire such as 302 and 316 grades. Hot-coiled work often uses 60Si2Mn and 51CrV4 alloy spring steels; quenched and tempered spring steels are typically used in the range 40-50 HRC. ASTM A228 covers oil tempered carbon steel wire for mechanical springs, and ASTM A401 covers chromium-silicon alloy spring wire, while JIS G 3521 covers oil tempered wire and SWOSC-V is a common chromium-silicon grade in that standard.
For a full view of coil types beyond round wire compression, see the springs product range. ISO 10243 covers rectangular section helical compression springs for stamping dies, and DIN 2093 covers disc springs and defines the group 1, 2 and 3 dimension series when your assembly mixes coil and disc elements.
Index, rate checks, and specifying inspection
The spring index D/d is normally kept between 4 and 12 so that compression springs remain manufacturable. When index or active coils change during prototyping, tolerance stacks on free length and solid height move quickly, so lock the inspection heights on the drawing before you freeze tool steel or fixtures.
Use calculated rate as a sanity check against measured load at a specified installed height. Before you release tolerances to production, run the same geometry through the spring rate calculator so design and shop paperwork stay aligned.
Spring wire acceptance often references GB/T 239.1 for the simple torsion test of metallic wire. Coated parts may be evaluated with salt spray testing per ASTM B117; zinc-nickel plating, zinc flake and epoxy powder coating are common corrosion protection systems for springs. Hot-coiled railway suspension springs are commonly made from bar diameters of about 20-45 mm and are shot peened to improve fatigue life, a treatment also widely applied to suspension springs to raise fatigue strength.
| Drawing control | Typical use |
|---|---|
| Free length | Stack-up and assembly clearance |
| Solid height | Maximum travel and nesting |
| Load at installed height | Functional preload and rate confirmation |
Railway fastening springs are commonly supplied to meet railway standards and are tested for load and fatigue; for vehicle programs, review automotive suspension springs alongside your EN 15800 quality notes so protection systems and peening requirements stay on one checklist.
FAQ
Which EN standard covers design calculation versus cold coil quality for round wire compression springs?
EN 13906-1 covers the design calculation of cylindrical helical compression springs made from round wire and bar. EN 15800 defines quality specifications for cold coiled compression springs made of round wire.
What wire diameter range and spring index D/d are normally assumed for manufacturable compression coils?
Spring wire diameters commonly range from 0.1 mm to 60 mm. The spring index D/d is normally kept between 4 and 12 so that compression springs remain manufacturable.
Which three drawing dimensions are most often controlled for compression spring tolerances on load and height?
Free length, solid height and load at a specified installed height are the three dimensions most often controlled on a spring drawing. Those controls tie directly to stack height and functional preload.
Closing notes for buyers and designers
Pair EN 13906-1 calculations with EN 15800 acceptance language on the same drawing so rate, height, and load tolerances stay traceable from design through inspection. When a program also needs bogie hardware, compare notes with railway bogie springs or custom disc springs before you split tolerances across mixed assemblies.
Email liu@chenjisprings.com or call +86 158 5311 1612, or Request a Quote at chenjisprings.com with your EN 13906-1 geometry and EN 15800 quality targets.
