ASTM A228 Springs: Oil Tempered Wire Grades and Sizes

ASTM A228 Springs: Oil Tempered Wire Grades and Sizes

What ASTM A228 Springs Are and Where They Fit

ASTM A228 springs are coiled from oil tempered carbon steel wire, a material class developed so that the spring maker receives wire already quenched and tempered and can coil it without a further hardening cycle. The standard covers oil tempered carbon steel wire for mechanical springs, and the wire is drawn to the finished diameter before the final heat treatment, which gives a clean surface and consistent mechanical properties along the coil.

Because the wire arrives in the tempered condition, ASTM A228 springs are typically cold coiled and then given a low temperature stress relief to stabilise the coils. This route suits high volume production of compression, extension and torsion springs where dimensional repeatability matters. Our custom spring range includes parts coiled from this wire class for mechanical assemblies, clamps, latches and general machinery.

Spring wire diameters commonly range from 0.1 mm to 60 mm, so the same material family spans micro springs and heavy coils. At the small end the wire is handled on precision coilers; at the large end the coil forces and the stress relief treatment become the dominant process considerations. The choice between oil tempered carbon wire and an alloy grade is driven by stress level, fatigue duty and the environment the spring will see in service.

It helps to separate the material standard from the design standard. ASTM A228 describes the wire; the coil geometry, stress and fatigue life are governed by design rules and by the drawing the customer approves. Both sides need to agree before a first article is coiled.

Wire Grades, Standards and Material Selection

Cold-coiled compression springs are usually made from patented cold drawn wire per EN 10270-1, with grades SL, SM, SH and DH covering increasing tensile levels. Oil hardened and tempered spring steel wire is covered by EN 10270-2, with grades FDC, TDC and VDC. These two families cover most cold-coiled work, while ASTM A228 remains the reference for oil tempered carbon wire in North American drawings.

Alloy and Stainless Alternatives

When stress or fatigue duty exceeds what carbon wire can carry, ASTM A401 covers chromium-silicon alloy spring wire, and JIS G 3521 covers oil tempered wire with SWOSC-V as a common chromium-silicon grade in that standard. For hot-coiled parts, 60Si2Mn and 51CrV4 are widely used alloy spring steels. Quenched and tempered spring steels are typically used in the range 40-50 HRC, which balances strength against toughness.

Corrosion resistance calls for a different family. Stainless spring steel wire is covered by EN 10270-3, with grades 1.4310 and 1.4401, and EN 10270-3 and ASTM A313 cover stainless spring wire such as 302 and 316 grades. These are the usual choice for food equipment, marine air and wet environments. A full overview of the wire families we coil sits on our compression spring pages.

Wire acceptance is not only about tensile. GB/T 239.1 covers the simple torsion test of metallic wire, a common acceptance test for spring wire, and spring surfaces are usually tested for decarburisation and for cracks with magnetic particle inspection on safety critical parts. Those checks catch surface conditions that a tensile test alone would miss.

Design Checks, Tooling and Corrosion Protection

Compression spring rate is calculated as k = G d^4 / (8 D^3 n), where d is wire diameter, D is mean coil diameter and n is the number of active coils. The spring index D/d is normally kept between 4 and 12 so that compression springs remain manufacturable, because coils that are too tight stress the wire during coiling and coils that are too loose are unstable. EN 13906-1 covers the design calculation of cylindrical helical compression springs made from round wire and bar, and EN 15800 defines quality specifications for cold coiled compression springs made of round wire.

Before a drawing is released, run the numbers with our spring rate calculator so that rate, load and stress are checked against the wire grade you intend to use. Free length, solid height and load at a specified installed height are the three dimensions most often controlled on a spring drawing, and all three follow directly from the coil geometry.

Other product families follow their own standards: ISO 10243 covers rectangular section helical compression springs for stamping dies, and DIN 2093 covers disc springs with the group 1, 2 and 3 dimension series. For hot-coiled railway suspension springs, bar diameters of about 20-45 mm are common and the parts are shot peened to improve fatigue life. Shot peening is widely applied to suspension springs to raise fatigue strength, and railway fastening springs are commonly supplied to meet railway standards and are tested for load and fatigue.

Corrosion protection is selected after the mechanical design is fixed. Zinc-nickel plating, zinc flake and epoxy powder coating are common systems, and salt spray testing per ASTM B117 is commonly used to evaluate coated springs. Review the options on our free engineering tools pages before specifying a coating.

FAQ

Which spring index range keeps a compression spring manufacturable?

The spring index D/d is normally kept between 4 and 12 so that compression springs remain manufacturable. Outside that band, coiling stresses or coil instability usually force a redesign of wire diameter or mean diameter.

What hardness range applies to quenched and tempered spring steels?

Quenched and tempered spring steels are typically used in the range 40-50 HRC. This range gives the strength needed for fatigue duty while retaining enough toughness for coiling and shot peening.

Which test covers the simple torsion test of spring wire?

GB/T 239.1 covers the simple torsion test of metallic wire, a common acceptance test for spring wire. It is combined with surface checks for decarburisation and, on safety critical parts, magnetic particle inspection for cracks.

Specifying and Ordering

Send the wire grade, the coil dimensions and the three controlled values on the drawing, and state the corrosion system and any test standard required. CHENJI SPRINGS coils ASTM A228 springs and the alloy and stainless alternatives described above, and we can review your drawing against the relevant design standard before quoting. Email liu@chenjisprings.com or call +86 158 5311 1612 to Request a Quote. You can also review torsion spring options and disc spring designs for adjacent parts of the same assembly.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top