Custom Wire Forms: Bend Radius, Springback and Tolerance
What Custom Wire Forms Demand From the Bending Process
Custom wire forms are shaped parts bent from round spring wire into hooks, loops, legs, arms and multi-plane geometries that a coil spring cannot deliver. Because they often act as clips, retainers, levers or contacts, the finished part must hold its geometry after forming and keep the load it was designed to carry. Spring wire diameters commonly range from 0.1 mm to 60 mm, so the same bending principles apply from fine instrument wire up to heavy bar stock, though the tooling and handling differ greatly.
Three variables decide whether a bent part meets its drawing: bend radius, springback and tolerance. Bend radius sets the strain on the outside of the wire and therefore the risk of cracking or losing section shape. Springback is the elastic recovery after the bending tool releases, which pulls the bend angle back toward straight. Tolerance is the window that remains after both effects are managed. A part that looks correct on the press but opens up during inspection has usually been quoted without accounting for the wire grade and its temper.
Wire forms are usually produced alongside coil springs in the same shop, and the material behaviour is shared. The range of spring and wire form products typically covers compression, torsion and extension coils as well as bent wire parts, which means the wire lot, coating and inspection route can be planned together. That matters most when a wire form has to mate with a spring in the same assembly.
Standards and Materials Behind Reliable Custom Wire Forms
Material selection starts with the wire standard. Cold-coiled compression springs are usually made from patented cold drawn wire per EN 10270-1 (grades SL, SM, SH, DH), and the same wire is common for small bent forms. Oil hardened and tempered spring steel wire is covered by EN 10270-2 (grades FDC, TDC, VDC), while stainless spring steel wire is covered by EN 10270-3 (grades 1.4310, 1.4401). For heavier sections, 60Si2Mn and 51CrV4 are widely used alloy spring steels for hot-coiled springs, and quenched and tempered spring steels are typically used in the range 40-50 HRC.
Wire Grades for Bent and Formed Parts
Where a wire form needs both strength and a defined surface finish, oil tempered carbon steel wire per ASTM A228 and chromium-silicon alloy spring wire per ASTM A401 are common references. JIS G 3521 covers oil tempered wire, with SWOSC-V a common chromium-silicon grade in that standard. Stainless grades such as 302 and 316 are covered by EN 10270-3 and ASTM A313, and they are chosen when the part works in a wet or mildly corrosive environment and a coating is not wanted.
Acceptance testing should be agreed at the wire stage, not only on the finished part. GB/T 239.1 covers the simple torsion test of metallic wire, which is a common acceptance test for spring wire and gives an early signal on ductility before bending. Spring surfaces are usually tested for decarburisation, and cracks are checked with magnetic particle inspection on safety critical parts. Where the wire form is a torsion-type part, the same engineering logic as custom torsion springs applies to leg position and angular load.
Setting Bend Radius, Springback and Tolerance in Production
Bend radius is the first decision because it fixes the strain level. A radius that is too tight for the wire grade forces the outer fibres past what the material will take, and the part either cracks or shows a flattened section. Springback is then measured on the first article and compensated in the tool: the bend is over-bent so that it recovers to the drawing angle. Because springback changes with wire grade, temper and diameter, a tool set for one lot cannot be assumed correct for the next, and the compensation is verified again at each wire change.
Tolerance follows from the process window. Free length, solid height and load at a specified installed height are the three dimensions most often controlled on a spring drawing, and bent forms add angle and leg-length tolerances to that list. Design rules from EN 13906-1 for cylindrical helical compression springs made from round wire and bar, and the quality specifications of EN 15800 for cold coiled compression springs made of round wire, give a useful reference for what a stable process can hold. Keeping the spring index D/d between 4 and 12 keeps coiled parts manufacturable, and the same discipline of avoiding extreme geometry applies to bends.
For rate and stress checks on the coil side of an assembly, the spring rate is calculated as k = G d^4 / (8 D^3 n), where d is wire diameter, D is mean coil diameter and n is the number of active coils. Running that calculation through the spring rate calculator before tooling is released avoids rework when a wire form and its spring share a load path. Rectangular section parts follow ISO 10243, and disc springs follow DIN 2093 with its group 1, 2 and 3 dimension series, so mixed assemblies can be checked against the right reference.
| Parameter | Reference | Effect on the Formed Part |
|---|---|---|
| Wire diameter | 0.1 mm to 60 mm | Sets tooling size and handling method |
| Spring index D/d | 4 to 12 | Keeps coiled sections manufacturable |
| Hardness, quenched and tempered | 40-50 HRC | Drives springback and crack risk |
FAQ
How much springback should be allowed when bending 1.4310 stainless wire?
Springback depends on wire diameter, temper and the bend radius used, so it is measured on the first article rather than assumed. The tool is then over-bent to compensate, and the setting is rechecked at each wire lot change.
Which wire standard applies to a bent form that also carries a fatigue load?
Patented cold drawn wire per EN 10270-1 is common for cold-formed parts, while oil hardened and tempered wire per EN 10270-2 suits higher strength needs. The grade is agreed with the fatigue requirement and confirmed by the wire torsion test.
How is corrosion resistance verified on a coated wire form?
Salt spray testing per ASTM B117 is commonly used to evaluate the corrosion resistance of coated springs and formed parts. Zinc-nickel plating, zinc flake and epoxy powder coating are the usual systems, selected to suit the service environment.
Closing Notes on Wire Form Development
The practical route is to fix the wire grade and bend radius first, measure springback on the first article, and only then lock the tolerance band on the drawing. CHENJI SPRINGS produces custom wire forms together with compression, torsion and disc springs, and can review a drawing against the wire standard before tooling starts. Send your geometry, wire grade and load requirement to liu@chenjisprings.com or call +86 158 5311 1612, or Request a Quote. Related pages: coil spring manufacturing and free engineering tools.
