Disc Springs According to DIN 2093: Dimensions, Materials and Stacking
What DIN 2093 Defines for Belleville Disc Springs
A disc spring din 2093 arrangement delivers high force in a short axial stroke, which is why stacked Belleville washers appear in bolted joints, clutches, and safety-critical pre-load paths. DIN 2093 covers disc springs and defines the group 1, 2 and 3 dimension series, giving engineers a shared vocabulary for outer diameter, material thickness, and free height when comparing suppliers or revising legacy drawings.
Unlike a cylindrical helical member rated with k = G d^4 / (8 D^3 n), a disc spring din 2093 element behaves as a conical shell: stiffness rises sharply as the washer approaches solid height. Drawings for any spring family often control free length, solid height and load at a specified installed height; disc stacks follow the same discipline so installed load stays repeatable after thermal cycles or wear.
CHENJI SPRINGS manufactures disc and coil products for industrial and mobility applications. When you need a documented stack rather than a one-off washer, review the custom Belleville options alongside your joint layout and bolt travel limits.
Choosing the correct group and stack orientation early avoids rework on tooling and heat treatment. The sections below map materials to DIN expectations, then walk through selection, stacking rules, and common drawing questions.
Materials, Heat Treatment, and Related Wire Standards
Disc spring strip is typically quenched and tempered spring steel used in the range 40-50 HRC so the washer can store elastic energy without permanent set. Oil hardened and tempered spring steel wire is covered by EN 10270-2 (grades FDC, TDC, VDC); cold-coiled compression springs are usually made from patented cold drawn wire per EN 10270-1 (grades SL, SM, SH, DH). Stainless spring steel wire is covered by EN 10270-3 (grades 1.4310, 1.4401), and EN 10270-3 and ASTM A313 cover stainless spring wire such as 302 and 316 grades when corrosion resistance is required.
Hot-coiled alloy grades such as 60Si2Mn and 51CrV4 are widely used alloy spring steels for hot-coiled springs; they illustrate the same fatigue mindset applied to disc stacks that see millions of cycles. Shot peening is widely applied to suspension springs to raise fatigue strength, and the same surface treatment philosophy can be extended to highly cycled disc packs when the application warrants it.
Inspection and Acceptance Practices
Spring surfaces are usually tested for decarburisation and for cracks with magnetic particle inspection on safety critical parts. Salt spray testing per ASTM B117 is commonly used to evaluate the corrosion resistance of coated springs; zinc-nickel plating, zinc flake and epoxy powder coating are common corrosion protection systems for springs. GB/T 239.1 covers the simple torsion test of metallic wire, which is a common acceptance test for spring wire when round stock is supplied for downstream forming.
For programmes that mix disc washers with helical backup springs, wire diameters commonly range from 0.1 mm to 60 mm across the broader spring catalogue. Browse compression and wire forms when a single purchase order must cover Belleville stacks and companion coils governed by EN 15800 or EN 13906-1 design practice.
Dimension Series, Stacking, and Design Checks
DIN 2093 organises disc springs into group 1, 2 and 3 dimension series. Group choice trades outer envelope against force capacity: larger series fit bigger bores, while thinner groups suit compact stacks. Document parallel versus series stacking on the drawing so assembly torque maps to the intended pre-load rather than to accidental stiffening.
When disc springs sit near helical components, remember the spring index D/d is normally kept between 4 and 12 so that compression springs remain manufacturable; disc stacks should still be checked against bolt stroke so neither member bottoms early. Railway fastening springs are commonly supplied to meet railway standards and are tested for load and fatigue—a useful benchmark for high-cycle disc joints even outside rail.
| Group | Typical use | Drawing focus |
|---|---|---|
| Group 1 | Standard industrial pre-load | Outer diameter and free height per series table |
| Group 2 | Intermediate envelopes | Stack height versus bore clearance |
| Group 3 | Compact, high-force stacks | Load at installed height and solid height |
ISO 10243 covers rectangular section helical compression springs for stamping dies; it does not replace DIN 2093 for Belleville parts, but it reminds designers that dissimilar spring types should not share one calculation sheet. Use the spring rate calculator when you must reconcile a helical backup rate with a disc spring din 2093 stack before releasing tolerances.
Hot-coiled railway suspension springs are commonly made from bar diameters of about 20-45 mm and are shot peened to improve fatigue life; large mobility programmes sometimes pair similar bar stock philosophies with heavy disc packs. For torsion-heavy layouts, see custom torsion layouts that complement axial Belleville pre-load.
FAQ
How do DIN 2093 groups 1, 2 and 3 change stack height for the same bore?
Each group fixes a dimension series under DIN 2093, so outer diameter and thickness differ for a given bore. Pick the group first, then count washers so installed height matches free length, solid height and load at a specified installed height on the drawing.
Which hardness range is typical for quenched and tempered disc spring steel?
Quenched and tempered spring steels are typically used in the range 40-50 HRC for elastic elements that must resist set. Confirm heat treatment on the mill certificate and re-check after grinding or coating that removes material from the working surfaces.
Can EN 10270-3 grades 1.4310 or 1.4401 be specified for corrosive disc spring stacks?
Stainless spring steel wire is covered by EN 10270-3 (grades 1.4310, 1.4401), and EN 10270-3 and ASTM A313 cover stainless spring wire such as 302 and 316 grades. Match the grade to the environment, then validate coated or bare parts with salt spray testing per ASTM B117 when corrosion resistance is contractual.
Next Steps for Your Stack Drawing
Release group number, stack pattern, and installed-height load together so shop and field assembly interpret the disc spring din 2093 requirement the same way. Pair the Belleville note with corrosion system call-outs when the joint sees outdoor or chemical exposure.
Email liu@chenjisprings.com or call +86 158 5311 1612, and Request a Quote with bore, stroke, and target load. Related programmes often combine custom coil springs with railway suspension coils in the same bill of materials.
